THE SOLUTION
HEAVY DUTY TRUCK WASH

PRODUCT DESCRIPTION:
The SOLUTION is designed to clean the inside and outside of over the road tractors, trailers and other type commercial vehicles. It will clean and brighten aluminum surfaces as well as painted surfaces without damage when used as directed. This product will remove carbon stack stain and magnetic road film from trailers without brushing. It is designed for heavy duty cleaning such as drive through truck washes. The SOLUTION will work in cold water as well as hot water, and rinse free at any temperature.

DIRECTIONS:
For use in hot pressure washers, apply to the surface at the rate of 1 part cleaner to 50 parts water. For use in cold pressure washers and cold water drive through truck wash systems use at the rate of 1 part cleaner to 25 parts water. When cleaning with pressure washers, always apply cleaning solutions from the bottom up on a dry surface. Always detail clean from the bottom up and rinse from the top down. DO NOT USE ON POLISHED OR ANODIZED ALUMINUM. DO NOT USE ON ANY ALUMINUM OR PAINTED SURFACES AT CONCENTRATIONS OF LESS THAN 1:40. DO NOT ALLOW TO DRY

TRUCK BRITE
TRUCK WASH

PRODUCT DESCRIPTION:
Truck Brite is designed to safely clean polished aluminum and painted surfaces of over the road tractors, trailers, and other type commercial vehicles without damage when used as directed. This product will remove magnetic road film from trailers without brushing. It will work in cold water as well as hot water, and rinse free at any temperature. It is designed for
heavy duty cleaning such as drive through truck washes.

DIRECTIONS:
For use in hot pressure washers, apply to the surface at the rate of 1 part cleaner to 25 parts water. For use in cold pressure washers and cold water drive through truck wash systems use at the rate of 1 part cleaner to 20 parts water. When cleaning with pressure washers, always apply cleaning solutions from the bottom up on a dry surface. Always detail clean from the bottom up and rinse from the top down. DO NOT USE ON PAINTED SURFACES AT CONCENTRATIONS OF LESS THAN 1:15. DO NOT ALLOW TO DRY ON PAINTED SURFACES. ALWAYS RINSE THOROUGHLY.

JL-20
ONE STEP
TRUCK WASH

PRODUCT DESCRIPTION:
JL-20 is a one step truck washing compound designed to clean painted trucks and trailers. To achieve best results JL-20 must be used in a hot water washer. When used as directed JL-20 will remove magnetic road film, grease and grime from all painted surfaces including chassis and engines.

DIRECTIONS:
For use in hot pressure washers, apply to the surface at the rate of 1 part cleaner to 35 parts water. For use in cold pressure washers and cold water drive through truck wash systems use at the rate of 1 part cleaner to 20 parts water. When cleaning with pressure washers, always apply cleaning solutions from the bottom up on a dry surface. Always detail clean from the bottom up and rinse from the top down. DO NOT USE ON PAINTED SURFACES AT CONCENTRATIONS OF LESS THAN 1:15. DO NOT ALLOW TO DRY ON PAINTED SURFACES. ALWAYS RINSE THOROUGHLY.

#1 WASHING SYSTEM

PRODUCT DESCRIPTION:
This is the first step of a two step cleaning system designed to be used with a two step cold water high pressure washer. This system was designed to clean over the road trucking equipment such as trailers and tractors. This system when used as directed, is the most efficient cleaning system available today and will remove heavy soils including carbon stack stain
from diesel exhaust and the hard to remove magnetic road film on painted surfaces.

DIRECTIONS:
DO NOT RUN THIS PRODUCT THROUGH PUMPING SYSTEM OR HEATING COILS. Apply NO. 1 at the rate of 1 part chemical to 25 parts water on a dry surface from the bottom up. Without rinsing, apply NO. 2 over NO. 1 from the bottom up. Detail clean from the bottom up and rinse from the top down. DO NOT USE ON GLASS OR ANODIZED ALUMINUM. DO NOT USE ON DELICATE PAINT. DO NOT ALLOW TO DRY ON SURFACES. ALWAYS RINSE THOROUGHLY.

#2 WASHING SYSTEM

PRODUCT DESCRIPTION:
This is the second step of a two step cleaning system designed to be used with a two step cold water high pressure washer. No. 2 is for use in cleaning over the road equipment such as trailers and tractors. This system when used as directed, is the most efficient cleaning system available today and will remove heavy soils including carbon stack stain from diesel exhaust
and the hard to remove magnetic road film from painted surfaces without brushing. It will work in cold water as well as hot water, and rinse free at any temperature. It is designed for heavy duty cleaning such as drive through truck washes.

DIRECTIONS:
Without rinsing, apply NO. 2 at the rate of 1 part chemical to 25 parts water from the bottom up. Detail clean from the bottom up and rinse from the top down. DO NOT USE ON ANODIZED OR POLISHED ALUMINUM. DO NOT USE ON ANY ALUMINUM OR PAINTED SURFACES AT CONCENTRATIONS OF LESS THAN 1:20. DO NOT ALLOW TO DRY ON SURFACES. ALWAYS RINSE THOROUGHLY.

ALUMA-NEW HD
Aluminum Brightener

PRODUCT DESCRIPTION:
ALUMA-NEW HD will clean and brighten unpainted aluminum without damage when used as directed. It will work in cold water as well as hot water.

DIRECTIONS:
DO NOT RUN THIS PRODUCT THROUGH PUMPING SYSTEM OR HEATING COILS. Optimum dilution of this product is 1 part chemical to 30 parts water when applied down stream with a pressure washer. Used in a pump sprayer mix 4 ounces of chemical to each 1 gallon of water. In hard water areas more chemical may be required. Always
test chemical in and out of the way area. When cleaning with pressure washers, set the metering valve at desired dilution rate, and apply cleaning solution from the bottom up on a dry surface. Always detail clean from the bottom up and rinse from the top down. DO NOT USE ON GLASS OR ANODIZED ALUMINUM. DO NOT USE ON DELICATE PAINT. DO NOT ALLOW TO DRY ON SURFACES. ALWAYS RINSE THOROUGHLY.

SP-222
POLISHED ALUMINUM CLEANER

PRODUCT DESCRIPTION:
SP-222 is a ready to use complex formulation of environmentally friendly dilute acids and unique stable
biodegradable surface active detergents. This product is designed for cleaning Semi Dumps Bulk Carriers Horse Trailers, Wheels and Fuel Tanks that have a polished aluminum finish. SP-222 is designed to effectively remove residual dirt, oils, black welding soot, corrosion oxide films, design marker and microscopic projections from polished and extruded aluminum surfaces without etching or pitting.

CONCRETE TRUCK CLEANER

PRODUCT DESCRIPTION:
CONCRETE TRUCK CLEANER rtu will clean without damage when used as directed. It will work in cold water as well as hot water.

DIRECTIONS:
DO NOT RUN THIS PRODUCT THROUGH PUMPING SYSTEM OR HEATING COILS. Optimum dilution of this product is 1 part chemical to 10 parts water when applied down stream with a pressure washer. Used in a pump sprayer, mix 12 ounces of chemical to each 1 gallon of water. In hard water areas more chemical may be required. Always test chemical in an 'out of the way' area. When cleaning with pressure washers, set the metering valve at desired dilution rate, and apply cleaning solution from the bottom up on a dry surface. Always detail clean from the bottom up and rinse from the top down. DO NOT USE ON GLASS, ANODIZED OR POLISHED ALUMINUM. DO NOT USE ON DELICATE PAINT. DO NOT ALLOW TO DRY ON SURFACES. ALWAYS RINSE THOROUGHLY.

DE-GREASE WD
HEAVY DUTY DEGREASER

PRODUCT DESCRIPTION:
DE-GREASE WD is a highly concentrated liquid detergent which is designed for heavy duty steam cleaning. It is formulated with the highest quality penetrants and surfactants to promote the rapid emulicification of dirt, grease, and oil. This product is designed to clean off road equipment like dozers, cranes, draglines, lifts and other commercial equipment. It will work best in hot water, and rinse free at any temperature.

DIRECTIONS:
The optimum cleaning dilution for most surfaces is between 1:30 and 1:50. When using DE-GREASE WD with pressure washers or steam cleaners, set the metering valve at desired dilution rate and apply cleaning solution from the bottom up on a dry surface. Always detail clean from the bottom up and rinse from the top down. DO NOT ALLOW TO DRY ON PAINTED SURFACES. DO NOT USE ON ANODIZED OR POLISHED ALUMINUM. DO NOT USE ON ANY
ALUMINUM SURFACES OR ANY PAINTED SURFACES AT CONCENTRATIONS OF OF LESS THAN
1:40. ALWAYS RINSE THOROUGHLY.

ECO-SOLVE
TAR & ASPHALT REMOVER

PRODUCT DESCRIPTION:
Eco-Solve Tar and Asphalt Remover is a balanced blend of 100% natural solvents derived from a renewable source. It is non toxic, biodegradable. Contains no chlorinated solvents or harsh chemicals and is non corrosive. Suitable for use on state paving jobs. Excellent for removel of tar and asphalt on trucks, paving equipment, tools and more. Quickly penetrates and loosens tar so it so it may be flushed away with water. Also excellent as a environmentally safe asphalt release agent.

DIRECTIONS:
Eco-Solve Tar and Asphalt Remover should not be diluted prior to use. Apply evenly to the surface with a sprayer or brush let stand until asphalt is softend rinse off with high pressure water. For asphalt release - Apply a uniform coating to the truck bed just before loading the asphalt mixture. This release does not effect bonding or physical strength of asphalt mix.

CITRACLEAN
CITRUS BASE CLEANER

PRODUCT DESCRIPTION:
The most universal heavy duty, all purpose cleaner & degreaser on today's market. Made from all natural citrus base ingredients. Biodegradable. Safe to the environment. 100% free from caustics or acids. No chlorinated solvents or petroleum distillates. Great for floors, ovens, stainless steel, RV's, mobile home exteriors, vinyl & aluminum siding, gutters, carpets, upholstery, tires and machinery. Excellent automotive degreaser.

DIRECTIONS:
DILUTE WITH WATER
Floors, Walls, General Maintenance.
Light Soil ..............1 to 50
Medium Soil .........1 to 10
Heavy Soil ............1 to 5

CCS - 80
MULTI-TASK CLEANER

PRODUCT DESCRIPTION:
CCS-80 is a premium, high quality, concentrated cleaner degreaser that contains an organic solvent to help dissolve grease, oil, mold, mildew, soap scum, etc. It is very effective in the high pressure, cold or hot water washing of mobile homes, RV's, trucks, trailers, buildings, etc. CCS-80 is also an excellent pre-spray for use on extremely difficult cleaning jobs and will clean engines, vinyl, white wall tires, stainless steel, aluminum, painted surfaces, floors, walls and counter tops. The corrosion inhibitors and water softeners in CCS-80 help prevent rusting of ferrous metals.

DIRECTIONS:
CCS-80 is a concentrate; in most applications should be diluted prior to use. However, when used as a prespray, CCS-80 may be used full strength depending on severity of soil. When used through pressure washing equipment, drop detergent feed line into CCS-80 concentrate and set metering valve to desired setting, and soak entire surface from bottom up. Detail clean from bottom up. Rinse with fresh water from the top down.

CCS - 77
SOLVENT DEGREASER

PRODUCT DESCRIPTION:
CCS-77 is a premium, high quality grade self emulsifying solvent degreaser. Ideal for heavy duty general degreasing. Designed to clean all types of machinery and automotive engines and parts. CCS-77 is also an excellent product for the removal of road tar and asphalt from all types of vehicles and paving equipment.

DIRECTIONS:
CCS-77 May be used full strength or can be diluted up to 10 to 1 with mineral spirits. Apply with a sprayer for removal of tar and asphalt from paving equipment and to degrease equipment or truck chassis or use in parts washer sink to clean parts. Wipe off excess.

SOY-SOLVE
ASPHALT RELEASE AGENT

PRODUCT DESCRIPTION:
SOY-SOLVE Asphalt Release Agent is a 100% natural release solvent derived from a renewable source. It is non toxic, biodegradable. Contains no chlorinated solvents or harsh chemicals and is non corrosive. Suitable for use on state paving jobs. Excellent for removel of tar and asphalt on trucks, paving equipment, tools and more. Quickly penetrates and loosens tar so it so it may be flushed away with water. Also excellent as a environmentally safe asphalt release agent.

DIRECTIONS:
Soy-Solve Asphalt Release Agent should not be diluted prior to use. Apply evenly to the surface with a sprayer or brush let stand until asphalt is softend rinse off with high pressure water. For asphalt release Apply a uniform coating to the truck bed just before loading the asphalt mixture. This release does not effect bonding or physical strength of asphalt mix.

GLU-B-GONE
ADHESIVE & MASTIC REMOVER

PRODUCT DESCRIPTION:
GLU-B-GONE Adhesive & Mastic Remover is a 100% natural release solvent derived from a renewable source. It is non toxic, biodegradable. Contains no chlorinated solvents or harsh chemicals and is non corrosive. Suitable for use on all surfaces. Excellent for the removel of dried adhesive and sticky adhesive residue.

DIRECTIONS:
GLU-B-GONE Adhesive & Mastic Remover should not be diluted prior to use. Apply evenly to the surface with a sprayer or brush let stand until adhesive is softend and squeegee off with a bondo spreader. Then rinses free with water.